Aqua UltaViolet Quartz Sleeve 40-Watt
- Product Details
- Shipping
- Video
QUARTZ SLEEVE 40-WATT
Includes the Quartz Sleeve and the Rubber Seal for the Aqua UV 40 Watt.
CLICK ON THE IMAGE ABOVE FOR A LARGER VIEW TO ASSIST WITH THESE INSTRUCTIONS
INSTRUCTIONS TO REPLACE QUARTZ SLEEVE:
1. Unplug system, turn pump off, and drain housing.
2. Untwist E-Z twist top.
3. Untwist Quartz Cap. Push quartz sleeve up through E-Z Twist Top.
4. Discard broken quartz sleeve and rubber seal.
5. Reinstall E-Z twist top without quartz sleeve. Slide quartz sleeve in housing with rubber seal already on quartz sleeve. Be sure to center the quartz sleeve into the seat at the bottom of the unit.
6. Gently push quartz sleeve and rubber seal in E-Z twist top until ½ the rubber seal is showing equally around the quartz.
7. Twist on the Quartz cap. DO NOT use a pipe wrench, pliers or any other tool on this unit. Tighten by hand only.
8. Do not install lamp or electrical components yet. After all the connections have been made turn pump on and run it for five minutes to check for leaks.
9. If there are no leaks, turn pump off and continue to the electrical installation section.
If unit leaks turn pump off and continue.
10. If you notice a leak from between the quartz cap and the EZ Twist Cap, Undo quartz cap and push rubber seal into the housing evenly. The rubber seal should be ½ in and ½ out. Redo quartz cap and finger tighten. Do not use a pipe wrench, pliers or any other tool. Hand-tighten only. Then repeat step # 8.
11. If you notice a leak from between the EZ Twist cap and housing, Untwist and check that the O-ring is seated in the top of the EZ-Twist cap. Hand-tighten until leak stops. Do not use a pipe wrench, pliers or any other tool. Hand-tighten only.
12. If you notice a leak from the quartz sleeve, Repeat step # 8. If unit still leaks, then the quartz sleeve is broken and needs to be replaced. A broken quartz sleeve is not covered under warranty nor is any damage caused as a result of a broken quartz sleeve. A new quartz sleeve will need to be purchased.
Includes the Quartz Sleeve and the Rubber Seal for the Aqua UV 40 Watt.
CLICK ON THE IMAGE ABOVE FOR A LARGER VIEW TO ASSIST WITH THESE INSTRUCTIONS
INSTRUCTIONS TO REPLACE QUARTZ SLEEVE:
1. Unplug system, turn pump off, and drain housing.
2. Untwist E-Z twist top.
3. Untwist Quartz Cap. Push quartz sleeve up through E-Z Twist Top.
4. Discard broken quartz sleeve and rubber seal.
5. Reinstall E-Z twist top without quartz sleeve. Slide quartz sleeve in housing with rubber seal already on quartz sleeve. Be sure to center the quartz sleeve into the seat at the bottom of the unit.
6. Gently push quartz sleeve and rubber seal in E-Z twist top until ½ the rubber seal is showing equally around the quartz.
7. Twist on the Quartz cap. DO NOT use a pipe wrench, pliers or any other tool on this unit. Tighten by hand only.
8. Do not install lamp or electrical components yet. After all the connections have been made turn pump on and run it for five minutes to check for leaks.
9. If there are no leaks, turn pump off and continue to the electrical installation section.
If unit leaks turn pump off and continue.
10. If you notice a leak from between the quartz cap and the EZ Twist Cap, Undo quartz cap and push rubber seal into the housing evenly. The rubber seal should be ½ in and ½ out. Redo quartz cap and finger tighten. Do not use a pipe wrench, pliers or any other tool. Hand-tighten only. Then repeat step # 8.
11. If you notice a leak from between the EZ Twist cap and housing, Untwist and check that the O-ring is seated in the top of the EZ-Twist cap. Hand-tighten until leak stops. Do not use a pipe wrench, pliers or any other tool. Hand-tighten only.
12. If you notice a leak from the quartz sleeve, Repeat step # 8. If unit still leaks, then the quartz sleeve is broken and needs to be replaced. A broken quartz sleeve is not covered under warranty nor is any damage caused as a result of a broken quartz sleeve. A new quartz sleeve will need to be purchased.
